Gunfighters is the best. They have made me at least 10 holsters the last few years. It also helps that they are local here in N Idaho..

I have had the SCS on my 2.0 performance metal for close to a year now. Really like it..

Since they have moved to Idaho and are 15 minutes from my house I have made frequent trips there.. They are very accommodating and have made
a couple of custom Ronins for me. Love the chest rigs also..BTW they are in Rathdrum, between Coeur d Alene and Sandpoint in North Idaho..

Cop killer bullets?  Never heard that one.. My LE agency I worked for (10Ksworn) we were told that the black community did not like the round as they were black for shooting black people.  When the change came to the ranger SXT we were told SXT  meant same exact thing. 

I also went wet, I have SS pins and SS in granular form..

Quote from: sep on October 15 2022 05:43:41 AM MDT
I only load my hunting and woods defense cases a couple times. Then they become used for plinking loads til they split. Sometimes they split upon firing, sometimes they split when trying to seat a bullet. It's amazing how long they last.   

Most all of my 10mm gets run thru 1006-1076..and now M/P..

I have found that the 10mm case seem to budge at the base of the case. I loose about 10 per 100 that willl not seat in my case gauge after de priming and sizing in my Dillon 550.. I cant say how many times the brass has been reloaded.

I stopped using X-treme bullets due to the high cost. I load for target and recently switched to a polymer coated lead bullet. My latest load is 165 grain RNFP I can buy 750 for 82 bucks shipping included.You do need to bell the case a bit more.  My range partner and I have runs tests to see if the poly coating stays on the bullet. As far as we can tell the coating is very durable. I had used X-treme for many years until the costs became prohibitive. Take a look at " thebluebullets.com" and see what they have available I only order a quantity that has free shipping. Currently loading 9,40/10 and 45ACP.

I have a few more, way too many..

2  1006
3  1026
2  1046
3  1066
4  1076
1  1086
1  610
1  M/P 4.6
1  G20
1  G29

For some reason the 4" seem to be more troublesome than the 4.6. I have 6 magazines for my 4.6 no issues at all. I have 750 rounds down range so far. My target load is 165 grain polymer RNFP with 4.7 grains of 231. I did replace the captive recoil spring with a Wolff guide rod and heavier spring.

Hodgdon CFE pistol is one of the most versatile powders I have  found. Many of my reloading buddies have all started using this powder.I load 9 , 40 ,45 & 10 with this powder.

I had been on a list for 6-8 months and bought s service grade 1911. Colt match slide and barrel frame was made in 1943.

I just searched my holster box and located the thigh panel. Will have to wear it at the end of the month when
I work at range..

On the Ronin  with kydex belt loops I have them use thicker kydex as I seem to break the front one.. Stressing while bending over I guess.
I have a couple with the malice clips also.. I have been looking for my thigh panel must be in my holster box??  not sure where it went.. Have to look again..

They make one of the best Kydex holsters you can buy.. I was just at Gunfighters an hour ago..They are making a holster for
a friends 9mm revolver on "L" frame S&W. Last week they made an OWB for my S&W 10 with Steiner optic.