Shadow
Have you tried pushing this powder any faster?

Not for gen 4

I am not sure that it will fit a gen 4.. I don't think it will.  I will do some checking

Eaa P carry 10mm like new. Comes with wolff calibration kit.  $450 or offer. 269 7208625 I can send pictures.

Zev ultimate drop in adjustable trigger for large frame glock 20 and 21.  $200 shipped. Email durdy1@sbcglobal.net or text 269 720 8625... text for pics

Kkm 6 inch .40 conversion barrel for glock 20.  About 120 rds through it. Comes with lone wolf stainless captured guide rod and 14 lb spring $150 shipped email durdy1@sbcglobal.net text 269 720 8625.  Text for pics

Kkm 10mm barrel with about 100 rds through it. Comes with lone wolf stainless captured guide rod, and 22 lb spring.  $150 shipped. email durdy1@sbcglobal.net or text 269 7208625.  Text for pictures   Sold thanks

Glock 20 6 in longslide lone wolf.   Cerakote burnt bronze, with dawson percision competition sights. 270 for slide 80 cerakote 130 sights.  $480 into slide, asking $400.  All extras in pics included.  Less than 300 rds on slide. Email durdy1@sbcglobal.net. or text 269 7208625. I can't figure out pictures.   Says file too big.

Cool can't wait to get mine
..they just emailed me and said I will have to wait a bit longer there was a snafoo with my gun....owell I have waited 5-6 months now

So they are kinda tight. Lol.  What flat bottom block...so 22 lb recoil spring and 25 mainspring from what I have read elsewhere is a good start?

Well I just got word that my Dan Wesson razorback 10 will be in next week.  In preparation for it. I need some advice for the gun.  I plan doing a trigger job and new springs.  I plan on hunting with this gun and want nuclear loads.  I have been reading some on mainspring poundage and recoil spring.  I want to shot hot stuff mostly and hopefully not destroy the gun.  What are some thing I will need to do or look for, so I can make a list and bring it to the gunsmith.  thanks.  I too have been bitten my the 10mm bug.

My P carry is going back to eaa tomorrow.  Shooting 3-4 inches low ant 15 yds. I have about 300 rds throught it now. Most hot loads.  I have had feed issues.  I tried the sprinco guiderod with the wolff calibration kit.  I think the sprinco made it studder or short stroke.  I am pretty sure I am not limp wristing.  I put the stock guide rod back in and shot 18 20 and 22 lb springs with lots of ftf.  The springs are just slightly longer than the recoil rod.  They have been over stressed and compressed.  I talked to Alan at sprinco, and he feels that the internal spring channel has been changed some from the factory and I am .almost getting a solid sprig stack....  Alan is returning the guide rod and was trying figure out what changed so he can rework his product. 

  If the gun still had function issues when if comes back,  it will probably be up for sale.  I don't want to tinker or tweak.  I want a reliable gun.  And yes I am paying shipping both ways.  Customer service was pleasant speaking but suggested I buy a $95 adjustable sight.   Or send it back to make sure the barrel was set properly.

Well I put stock guide rod in. And I will run some rounds with wolff 18,20, and 22 springs in it...Gona send back sprinco.  Order a henning kit.  I just loaded some bayou bullet 180 gr with 11 gr of bluedot.  Will see how that goes.

Very nice.....when will it be out?

Intercooler should I just get the henning basic upgrade kit with extended firing pin?